phone 983-651-5611
Home > Event Id > Event Id 20106 Windows 2008

Event Id 20106 Windows 2008


I knew that it had something to do with that, but was unsure as to where I needed to disable them. If it's in LAN Routing only, the Internal interface is not a valid interface to be routed on because it is used for demand dial connections or receiving incoming VPN/Dial-In connections Not a member? The essential Virtualization resource site for administrators. this contact form

Are you certain? As the Knowledge Base contains no reference to 20106, I ran rrasmgmt.msc in the MMC Console and looked at the "General" tab under "Properties" for the local Server (router). I have set it up and remove it almost 4 times according to several different guides and previous settings. If you continue to get this error, contact Microsoft Product Support Services.

Unable To Add The Interface With The Router Manager For The Ipv6 Protocol

Difference between robotics and... A demand-dial interface is a logical interface that represents a point-to-point connection. Recently one of the other IT guys accidentally bricked the server and a whole reinstallation was required. Yes No Tell us more Flash Newsletter | Contact Us | Privacy Statement | Terms of Use | Trademarks | © 2016 Microsoft © 2016 Microsoft

Best Regards Elytis Cheng Please remember to click “Mark as Answer” on the post that Elytis Cheng TechNet Community Support Marked as answer by Elytis ChengModerator Monday, December 19, 2011 8:17 Right-Click on the server name and select 'All Tasks' Restart. Signup for Free! It has two NIC card, one connected to internet, and other connected to my private network.

The following error occurred: Cannot complete this function." Where should I start here? ISA server software Monitoring & Admin Reporting Security Services Featured Products Featured Book Order today TechGenix Sites The leading Microsoft Exchange Server 2010 / 2007 / 2003 resource site. ClintD Ars Scholae Palatinae Registered: Jan 13, 2000Posts: 1372 Posted: Sun Apr 01, 2001 3:17 pm Sorry, should've explained that a little more.Right click on the server and select Disable RRAS. Member Login Remember Me Forgot your password?

Might be worth a try. Enable the router check box as stated on the first suggestion. The following error occurred: Cannot complete this function. This seems incredibly difficult to setup for such a fundamental aspect of the network configuration. 0 Comment Question by:pcathome Facebook Twitter LinkedIn's.htmlcopy Best Solution bypcathome Up and running on

Event Id 20106 Cannot Complete This Function

The one difference I can see between the old and the new setup is that the Internal Broadcom Adapter has "No Internet Access" on the IPV4 address. read more... Unable To Add The Interface With The Router Manager For The Ipv6 Protocol Thanks! To connect to a remote access server: 1.In Network and Sharing Center, click Manage network connections. 2.Double-click the VPN connection, and then click Connect. 3.Verify that the connection was established successfully.

After removing it, the problem was solved. Will close thread for time being and come back to subject later. Expand the servername. Static filters configured for the Routing and Remote Access service will not be applied. 4.Warning RemoteAccess 20271 CoId={Number}; The user ****** connected from IP but failed an authentication attempt due

Magalhaes Stefaan Pouseele Blogs Books Hardware ISA Appliances SSL Acceleration Links Message Boards Newsletter Signup RSS Feed Software Access Control Anti Virus Authentication Backup & Recovery Bandwidth Control Caching Content Security All rights reserved.Newsletter|Contact Us|Privacy Statement|Terms of Use|Trademarks|Site Feedback home| search| account| evlog| eventreader| it admin tasks| tcp/ip ports| documents | contributors| about us Event ID/Source search Event ID: Event [email protected] replied Dec 27, 2016 at 6:00 PM Loading... I remember having this problem the first time and switching some setting and having it work.

Also in the VPN logs (in the tracing folder), I keep seeing this error when I restart the Remote Access service 12:58:52: AddInterface: Adding External NIC [308] 12:58:52: CreateIcb: Error 2 No, create an account now. LVL 30 Overall: Level 30 Windows Server 2008 9 MS Server OS 6 MS Legacy OS 6 Message Active today Expert Comment by:pgm554 ID: 225567062008-09-23 Correct me if I'm wrong,but doesn't

It turned out to be caused by the internal 1394 card.

Privacy Policy Support Terms of Use Log in or Sign up PC Review Home Newsgroups > Windows 2000 > Microsoft Windows 2000 RAS Routing > Error 20106 RemoteAccess HELP!!!!!! Static filters configured for Routing and Remote Access service will not be applied 3.Warning RemoteAccess 20219 IPv4 packet filtering has been disabled. Creating your account only takes a few minutes. An example of English, please!

About Us PC Review is a computing review website with helpful tech support forums staffed by PC experts. I would just try on the server that is giving you this error. 0 Chipotle OP shelzmike Jun 21, 2010 at 9:49 UTC I will try and then Click Network and Internet, click Network and Sharing Center, and then click Set up a connection or network. his comment is here You may need to add a route for to give it the gateway of the external NIC. 0 Message Author Comment by:pcathome ID: 225377392008-09-21 Thanks Netman66.

The point-to-point connection is based on either a physical connection, such as two routers connected over an analog phone line that uses modems, or a logical connection, such as two routers Copyright © 2014 TechGenix Ltd. Advertisements Have You Seen?