phone 983-651-5611
Home > Failed To > Failed To Initialize Swap File

Failed To Initialize Swap File


However, since virtual machine disk files can be configured for use with any virtual machine, the file may be locked by another virtual machine that is currently running.To determine if the You may have to set DRS to manual to ensure thatthe virtual machine powers on the correct host.If the virtual machine still does not get powered on, complete these procedures while In the example below, it is the swap that is still locked. To address this issue, seeTroubleshooting a virtual machine that has stopped responding (1007819).If the output from this command isgetstate() = off, the ESX host may be unaware of the file lock.For have a peek here

Removing the .lck file (NFS Only) The virtual machine's files may be locked via NFS storage. Please enter a reply. You must determine which virtual machine should have ownership of the file, then reconfigure your virtual machines to prevent this error from occurring again.As part of their operation, many virtual machine The host on which the virtual machine is registered typically holds the lock.

Failed To Create Swap File '/vmfs/volumes/

For example: /vmfs/volumes///.vmx Note: Record this information as it will be required in the remainder of this process. When you have a match, cold migrate the VM to the relavant ESX host and boot it. From the above example, the process ID is 3631: kill 3631 After stopping the process, you can attempt to power on the virtual machine or access the file/resource. Texmansru47 Mar 15, 2009 4:22 PM GMT There is also several other ways, since the ability to use 'ps auxfww' may eventually go away.

Rebooting the ESX host which is locking the files By this stage, you have already investigated for identifiable VMkernel and Service Console processes which have maintained locks upon the required files, Record this information as it is required in the remainder of this process on the ESXi server.Assess the virtual machines current state on the host:For ESX, run this command:# vmware-cmd When powering on the virtual machine, you see one of these errors: Unable to open Swap File Unable to access a file since it is locked Unable to access Virtual machine Vmk_lock_not_free Each line contains the full path of a virtual machine's .vmx file.

This command returns a list of running process that contain the name of the VM. Unable To Power On Vm File Is Locked as the files cannot be accessed by the servers while locked. Determining if the file is being used by a running virtual machine If the file is being accessed by a running virtual machine, the lock cannot be usurped or removed. additional hints In this example, the MAC address of the Service Console orvswif0interface of the offending ESX Server is00:13:72:66:E2:00.

Register. Vmk_not_found The pid of the VM is located in the second column of the results right after the username (typically root). In certain circumstances these locks may not be released when the VM is powered off. Note: VMFS volumes do not have .lck files.

Unable To Power On Vm File Is Locked

Tuesday, April 17, 2012 Could not power on VM - lock was not free The other day we experienced an incident on the SAN storage with high latency and even loss You have identified the server via thevmkfstools -Dcommand in earlier steps, thelsofutility yields no offending processes, and no other virtual machines are locking the file.The server should be restarted to allow Failed To Create Swap File '/vmfs/volumes/ To assess the virtual machines current state, run the command: vmware-cmd getstate If the output from this command is getstate() = on, the virtual machine has become unresponsive. Failed To Create Swap File '/vmfs/volumes/vsan Locating the lock and removing it Because a virtual machine can be moved between hosts, the host where the virtual machine is currently registered may not be the host maintaining the

View all posts by VaibhaV Nanoti Author VaibhaV NanotiPosted on August 7, 2013August 7, 2013Categories Virtualization, VMware Leave a Reply Cancel reply Enter your comment here... By submitting you agree to receive email from TechTarget and its partners. Posted by Jakob Fabritius Nørregaard at 6:00 AM Labels: ESX 4.1, Service Console, Troubleshooting, VM No comments: Post a Comment Note: Only a member of this blog may post a comment. The server should be restarted to allow the virtual machine to be powered on again. An Error Was Received From The Esx Host While Powering On Vm Failed To Create Swap File

However, since virtual machine disk files can be configured for use with any virtual machine, the file may be locked by another virtual machine that is currently running. He has been using, designing and deploying VMware based solutions since 2005 and Microsoft since 2012. Send me notifications when other members comment. Check This Out At the end of the file, look for error messages that identify the affected file.

We have to find out which server keeps file locked. Failed To Create Swap File '/vmfs/volumes/ Read Only The error and the log entry identify the virtual machine and files:Where applicable, open and connect the VMware Infrastructure (VI) or vSphere Client to the respective ESX host, VirtualCenter Server, or To move to the virtual machine's directory, run the command: cd /vmfs/volumes// Use a text viewer to read the contents of the vmware.log file.

Failed to power on VM by Artur Krzywdzinski · March 21, 2012 When the ESX server get unexpected restart, it might happen that some of  the VMs has a problem with

last 12 figures is a MAC address of the service console from server which keeps  file locked. Open a remote console window for the virtual machine. The output will be similar to:[] /.vmxVerify that the affected virtual machine appears in this list. File Is Being Locked By A Consumer On Host With Exclusive Lock To check for Service Console-based locks on non-ESXi servers, run the following command:
lsof | grep

Failed to initialize swap file ‘/volumes/4d8a07c2-b63cce23-a467-d8d385b8f298/vm01/vm01-3473aa90.vswp' : Lock was not free or other similar error : Failed to power on VM. If any additional virtual machines are configured to use the disk, determine if they are currently running. Privacy Reply Processing your reply... this contact form Note: ESXi servers do not have a Service Console and limit lock troubleshooting to the VMkernel.

To confirm that the virtual machine is registered on the server and obtain the full path to the virtual machine, run the command: vmware-cmd -l The output returns a list of Excerpts and links may be used, provided that full and clear credit is given to Artur Krzywdzinski and with appropriate and specific direction to the original content. Submit your e-mail address below.