phone 983-651-5611
Home > Failed To > Failed To Load Data From Configuration Database Hp Ux

Failed To Load Data From Configuration Database Hp Ux

Never underestimate the power of stupid people in large groups 0 Kudos Reply Stephen Doud Honored Contributor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to Basically if the SG commands do not get a reply from the daemon they will log messages similar to those above. Daily fight and struggle with (monster) server to deliver it flawlessly to (King)Client Humor HPUX LINUX SOLARIS POST ISSUE SCRIPTS PHOTOS HPSUPPORT REFERENCES Saturday, May 3, 2014 HPUX : cmviewcl : Check by doing: # what /usr/lbin/identd usr/lbin/identd: $Revision identd 2.7.4 (PHNE_26305) $ If the version is not sufficient you need to update to a later version of sendmail.

cmcheckconf: Failed to get the existing cluster configuration. # cmviewcl Failed to load data from configuration database. Thanks for any responses. Done Checking existing configuration ... i am running trusted systems. read the full info here

All rights reserved.800 East 96th Street, Indianapolis, Indiana 46240 ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: Connection to Sep 16 10:43:03.631 [7188] Cluster C_cluster has valid: offline online, checked: offline online, available: offline , flags 0x91020 Sep 16 10:43:03.631 [7188] Chose dh39 for cluster C_cluster but no online target There are numerous causes why a reply is not returned to the command. I loaded some patch bundles on one server, and suddenly cannot talk much to my cluster.

Login to the quorum server and update the file... Read and adhere to the Special Installation Instructions of the SG patch you are using. Unknown error in generic_ack from remote config daemon during token exchange. Users are not too bad ;-) Solved!

This was discovered using this command: $ cmquerycl Two systems with the same hostnames were reported as being a member of the C_cluster cluster. Sep 16 10:43:03.631 [7188] update_cluster_handle - Node dh40 is NOT set with VM flag. When you find those, then go through the README files for the patches and see what special actions you have to do when those are loaded. HPUX : Itanium EFI HP-UX low quorum Edit the AUTO file so we can boot when one disk is missing: # efi_cp -d /dev/rdsk/cxtxdxs1 -u /EFI/HPUX/AUTO /tmp/AUTO # vi /tmp/AUTO...

Mark,Is this Serviceguard 11.16 by any chance?If so you may have installed a patch which changes the way Serviceguard does authentication. run cmgetconf and get the present cluster configuration.#cmgetconf -v -c outputfile2. Exiting. If the SG command's response is delayed by 10s only, you should check if the server's primary lan is available.

Which left some shared memory and semaphore on the server. Answer/Solution FIX: 1) Change the hostnames of the new systems to unique values (including /etc/rc.config.d/netconf). 2) Edit /etc/hosts to reference the new hostnames. 3) Edit the cluster configuration file, updating the HPUX : Vgcreation in case of no mapfile. By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner

The amount of time between checks of Service Guard export RunnerSGInterval="30" 21. navigate here Error: Failed to lookup /cluster in configuration database.Error: Fail to load data from configuration database.Internal error: Unable to communicate with configuration database.Error: Unable to connect to configuration database.cmcheckconf : Unable to Update the ASCII cluster configuration file. 9. Make sure that the number of SG commands running in parallel is not too high.

Failed to load data from configuration database. So here it is. The system returned: (22) Invalid argument The remote host or network may be down. This lead to the conclusion that their hostnames were not unique and the other systems were responding to the cmcheckconf messages.

Why does the -i switch make a difference when identd was always disabled? (.rhosts files have always been disabled too)Sorry for the long post... Connected to localhost. Each inode stores all the info...

Why is it giving the error Unable to connect to node NODEXX: Permission denied?

you run cmcheckconf to add a node that is not currently member of the cluster and you run the cmcheckconf on the node that is to be added? I am actually running 11.14 serviceguard. Make sure these SG versions use most recent patch levels. Due to ServiceGuard's need for local hostname lookup, it is recommended that /etc/nsswitch.files be copied to /etc/nsswitch.conf as a starting configuration for hostname resolution.Cause 3 :Run the following command on both

Check the syslog file for more information. Received a generic_ack from the remote side. Thank you! this contact form Make sure access to the port 113/tcp is possible (listed as identd or auth port in /etc/services or NIS).

in patch texts for SG). # ls -l /usr/lbin/cmclconfd -r-xr--r-- 1 bin bin 3725848 Mar 14 2005 /usr/lbin/cmclconfd 3. Different types of failure will prompt different responses from Serviceguard. Received a generic_ack from the remote side. You can check this by determining how long cmclconfd -p (not the ones with -c!) is running already (use ps -ef).

This is fixed in PHNE_38906. 15.