phone 983-651-5611
Home > Return Code > Return Code 236

Return Code 236

Contents

If the cables are undamaged, the main board or electronic journal may be defective 146 No reply from command to electronic journal 1. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main this contact form

If a belt displays excessive wear or damage you may be able to replace it. Consider sending the dispenser to repair to have new sensors installed. 38 Blocked exit This status appears if the exit sensor is covered or defective when the dispenser starts. 1. Inspect the exit area to ensure nothing is blocking the exit sensor. If the voltages are not within tolerance, the cable or power supply may be defective. 4. https://archive.sap.com/discussions/thread/1402506

Cpic Return Code 017 Sap Return Code 731

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 5. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. If error fails to reset, or the error reoccurs in a short amount of time, consider replacing the SPED. 241 SPED Warning: Self Test error See Error Code 240 382 Dispenser Test the dispenser by completing several test dispenses. 5.

Look up the definition on the Hardware Status listing. 4. See Error Code 101, 302 or 306 B) Excessive rejects. Purge the dispenser using PURGE command. Make sure the connectors are seated securely on the main board and on the electronic journal. 4.

If the error clears, put the cash dispenser in service. 6. Make sure the tamper screw is secure to the SPED Module. The 11.0 code is binary compatible, so we did not recompile.Create a hashed alias in /etc/profile: a shell script wrapper for logins. https://community.hpe.com/t5/General/VMSTAT-returns-odd-exit-code-236/td-p/4774048 Remove advertisements Sponsored Links jim mcnamara View Public Profile Find all posts by jim mcnamara #3 11-27-2009 parkea2 Registered User Join Date: Nov 2009 Last Activity: 27 November

Inspect for jammed currency at the Diverter. Once they are displayed on the screen, print or save them to an external device. Clear the jammed currency.2. If the error persist, possible causes may be the modem or main board assembly. 193 Baud rate setting for electronic journal failed 1.

Sap Return Code 751

Learn more about SAP Q&A. A mechanical error has occurred. Cpic Return Code 017 Sap Return Code 731 If the error persists, replace the dispensing mechanism. If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism.

Make sure that the exit sensor is clean and operation correctly. 3. http://twaproductions.com/return-code/return-code-128-sql.html Purge the dispenser using the purge command from diagnostic menu. 2. Remove any jammed notes.2. If the error clears, put the cash dispenser in service. 5.

Determine what is causing the cassette to not stay locked in place. 4. If the test dispenser fails again, try testing while pushing in on the cassette. Inspect the note transport make sure all belts are on track and there is no currency jammed in the transport or exit areas. http://twaproductions.com/return-code/return-code-cmd.html Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct.

Test the TDM-100 by completing several Test Dispenses. Cassettes are taken out of service because of feed failures or excessive rejects. 1. Complete several Test Dispenses to verify correct operation. 3.

If these actions have no effect, replace the dispensing mechanism. 50 Interference recovery Possible damage due to static discharge1.

Make sure it is seated at the main board and at the printer control board at CN6. 5. Inspect main board to electronic journal communication cable for damage. Go to Solution. 372533.txt ‏1 KB 0 Kudos Reply All Forum Topics Previous Topic Next Topic 3 REPLIES VK2COT Honored Contributor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Replenish the paper.

Inspect electronic journal to dispenser communication cable for damage. Verify the quality of your incoming TCP-IP connection and your TCP-IP configuration. Inspect for jammed Currency in the feed path and at the Exit sensor. his comment is here Refer to Section 5 of the RL5000 Service Manual or the RL5000 Quick Reference Guide for instructions. 2.