Company Overview SimoTime Technologies was founded in 1987 and is a privately owned company. Ensure that the operator mounts the correct volume. For an OPEN or CLOSE statement with the REEL/UNIT phrase the referenced file is a non-reel/unit medium. 08 Attempted to read from a file opened for output. 09 No room in X'72' 114 Return Code=00 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a catalog irregularity, or there was insufficient storage for Catalog Check processing. http://twaproductions.com/return-code/vsam-return-code-160.html
For example, during REPRO REPLACE, two separate updates to the same record were attempted. X'73' 115 Return Code=08 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a severe catalog error. Make sure that programmers logical units are available and rerun the job. If this is a multi-step job, either divide it into separate jobs or provide ASSGN statements instead of simplified JCL. http://ibmmainframes.com/about13751.html
An attempt was made to load a key-sequenced file with an access type other than keyed. MVSFORUMS.com Forum Index -> Data Management View previous topic :: View next topic Author Message szsharmaBeginnerJoined: 13 Jan 2009Posts: 1Topics: 1Location: Singapore Posted: Wed Nov 30, 2011 6:02 am Post X'8C' 140 Return Code=08 Action=Request VSAM encountered an inconsistent spanned record (that is, one or more segments were incompletely updated to destroyed).
If you look up the IDC error message in the Messages and Codes manual, you can find out exactly what the 116 return code means. If the file was implicitly defined, you can cause open to implicitly DISP = NEW. Instruct the operator to ensure that the device on which the volume mounting is done is in "up" status and unreserved before replying `NEWPAC'. PROGRAMMER ACTION: Change your application program to avoid attempts to open an ACB that is already open.
X'98' 152 Return Code=08 Action=OPEN Security verification failed: the password specified in the ACB or supplied by the operator for a specific level of access does not match the password in Vsam Open Return Code Is 160 Change your program to avoid task contention for the ACB. PROGRAMMER ACTION: Retry. CONDITION CODE IS 12 IDC0002I IDCAMS PROCESSING COMPLETE.
One of my Job abended while taking backup of an ESDS IAM file (say file name is - XXXX.YYYY.ZZZZ) with the reason - Code: IDC3300I ERROR OPENING XXXX.YYYY.ZZZZ file IDC3351I ** Save the dump you obtain for later problem determination. Message 42261 will be issued at end-of-job step for this file. The error may be caused by such condition as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.
Return Code=08 Action=Request A request other than sequential or skip sequential PUT to insert record was issued during initial loading of the file, or a request other than PUT insert was http://www.mvsforums.com/helpboards/viewtopic.php?p=58720 Refer to the section for Status-Key-1 being equal to "3" for additional information based on Status-Key-2. 4Logic Error, a program is attempting a file access function in an improper sequence or Vsam Open Return Code Is 168 System Action: Close processing continues to successful completion, assuming no other complications. Vsam Open Return Code Is 118 Rerun the job.
RESOURCE NOT AVAILABLE' 007500 WHEN '94' DISPLAY 'VSAM - SEQUENTIAL READ AFTER END OF FILE' 007600 DISPLAY 'OR NO CURRENT REC POINTER FOR SEQ' 007700 WHEN '95' DISPLAY 'VSAM - INVALID this content There may have been problems in loading the resource table. Run the Catalog Check Service Aid against the entire catalog; it will identify catalog errors for you. If circumstances indicate that no more extent blocks are available, rerun the job together with other jobs that require a smaller number of extent blocks (in a multiprogramming environment), or restructure
In this case, the physical size of the new record is allowed to be smaller than that of the record being replaced. 46 A sequential READ operation has been tried on X'0F' 015 Return Code=04 Action=COMM The work area provided in your program does not begin on a fullword boundary (GENCB or SHOWCB). Message 4A371 is issued to provide the catalog management return code and reason code which are used to diagnose the problem. weblink The device on which the volume is mounted "down" (Job Control command DVCDN).
Save the dump you obtain and SYSLOG output for later problem determination. A copy of the file was exported with the INHBITSOURCE options and imported into this system. The previous time the file was opened was the initial load of the file, and SPEED was specified.
Return Code=08 Action=OPEN VSAM could not obtain a contiguous area of virtual storage larger enough to accommodate work area, control blocks, and buffers needed by VSAM. This document may be used to assist as a tutorial for new programmers or as a quick reference for experienced programmers. If you do not use simplified job control, use LISTCAT output to determine which volumes must be described in the EXTENT statements. It compares HURBA value, number of index levels, system time-stamp and many other fields.
Attempt has been made to store a record that would create a duplicate key in the indexed or relative file OR a duplicate alternate record key that does not allow duplicates. Return Code=08 Action=Request For SHAREOPTIONS(4), the file size is too large for the control area size. SimoTime Technologies shall not be liable for any direct, indirect, special or consequential damages resulting from the loss of use, data or projects, whether in an action of contract or tort, check over here Downloads & Links This section includes links to documents with additional information that are beyond the scope and purpose of this document.
If record were only retrieved no programmer action is required. PROGRAMMER ACTION: Change your program to specify MACRF=OUT in the ACB if you want to process empty files. X'43' 067 Return Code=08 Action=OPEN An attempt was made to open an unexpired file for output using a DTF. PROGRAMMER ACTION: Only one OPEN, CLOSE, or Control Block Manipulation macro may use an ACB at a time.
Redefine and reload the file. For recoverable catalogs, VSAM always assigns a programmer logical unit for each CRA. This will not restrict files that use a max-CA for the control area size. Use Access Method Services EXPORTRA command to export the file for subsequent reimportation.
The VERIFY command is not used to determine whether or not a file exists. PROGRAMMER ACTION: Have your program executed in a larger virtual partition. Alternate indexes are incorrectly defined (Key length or position, duplicates or sparse parameters). 2. Return Code=08 Action=Request VSAM encountered end of file (during sequential retrieval), or the search argument is greater than the highest existing key (or relative record number) in the file.
Many vendors take advantage of the x"00' to x'FF' (or 0-255) binary value.