phone 983-651-5611
Home > Return Code > Vsam Verify Return Code 100

Vsam Verify Return Code 100

Contents

Hex. VSAM error codes which appear on the MVS job log and on the console. ******* you may copy this COBOL code and put it into your COBOL progrqam ******* to handle The Catalog Check Service Aid is documented in VSE/VSAM Programmer's Reference. Verify that your program is using the correct catalog. http://twaproductions.com/return-code/vsam-return-code-160.html

Return Code=08 Action=OPEN A permanent I/0 error was detected on the system lock file. X'42' 066 Return Code=08 Action=OPEN An attempt was made to open a DTF with file characteristecs that are incompatible with the file's cdharacteristics in the VSAM catalog. The record may contain segments at different update levels. The operator specified `NEWPAC' in response to a mount message, but did not actually mount the volume. http://ibmmainframes.com/about40482.html

Vsam Return Codes

X'48' 072 Return Code=08 Action=OPEN The file-id specified in your DLBL statement was not found in the catalog, and insufficient allocation information was specified for an implicit define. If the problem persists, instruct your operator to issue the ROD command and to run EREP (see VSE/Advanced Functions SADP); contact your IBM Support Center. The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.

PROGRAMMER ACTION: Change your DLBL statement to specify a valid file-id and rerun the job. An example is GETVIS failure. To VSAM, however, the file is not really open, so close disposition processing does not take effect when the file is closed. Vsam Open Return Code Is 160 For recoverable catalogs, VSAM always assigns a programmer logical unit for each CRA.

PROGRAMMER ACTION: Regenerate the file specifying a larger primary and/or secondary allocation in the Access Method Service DEFINE command, so that a larger control area size will be used by VSAM. Vsam Return Code 28 Rerun the job after the system problem is corrected. A GETVIS failure, or a failure to load a VSAM phase occurred. The file is a SAM ESDS in non-CI format, so OPEN did not try to verify its catalog records.

Save the dump you obtain and the SYSLOG output for later problem determination. Iec161i Updating is not permitted. Smaller than to record (slot) size specified for a relative-record file. PROGRAMMER ACTION: Change the reset specification and rerun your job.

Vsam Return Code 28

PROGRAMMER ACTION: Retry. There may have been problems in loading the resource table. Vsam Return Codes MACRF = LSR (local shared resources) has been specified together with UBF (user buffering). Vsam Open Return Code Is 168 X'54' 084 Return Code=08 Action=Request Locate mode was specified for a PUT request of for processing in a user buffer.

PROGRAMMER ACTION: Either correct the situation that caused the catalog recovery operation for this file to fail, or recreate the file. news Rerun the job. Return Code=04 Action=Request An attempt was made to change record length during update with addressed access or to change record length for a relative-record file. PROGRAMMER ACTION: Retry. Idc3009i

Detailed Error Information: ModuleIIS Web Core NotificationMapRequestHandler HandlerStaticFile Error Code0x80070002 Requested URLhttp://mainframegeek.me:80/abend-codes-and-explanation/ Physical PathE:\web\mainfram\abend-codes-and-explanation\ Logon MethodAnonymous Logon UserAnonymous More Information: This error means that the file or directory does not exist The information about volume is retrieved from the catalog, and programmer logical units are automatically assigned by VSAM. The Catalog Check Service Aid is documented in VSE/VSAM Programmer's Reference. http://twaproductions.com/return-code/vsam-return-code-116.html Books on Vsam Vsam Manuals / Tutorials VSAM error code, VSAM file status, VSAM/QSAM status key, abend codes error code, file status, status key, VSAM open error, QSAM open error, VSAM

Return Code=08 Action=Request No record found. Do not specify REPLACE under these circumstances. Either: A programmer logical unit is not available in this partition (available programmer logical units have been used by ASSGN job control statements, or VSAM automatic assignments for files, catalogs or

PROGRAMMER ACTION: Rerun your job when there is less concurrent activity in the system.

PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened. X'03' 003 Return Code=04 Action=CBMN An invalid keyword has been specified for GENCB/MODCB/SHOWCB/TESTCB. Note: VSAM produces an INDUMP of the region containing the VSAM control blocks, provide the SYSDMP is created and assigned. X'40' 064 Return Code=08 Action=OPEN An attempt was made to open a NOCIFORMAT file using an ACB.

The most common problems are: Not enough partition GETVIS space. Note: VSAM provides an IDUMP of the region cotaining the VSAM control blocks, provided the SYSDMP is assigned. PROGRAMMER ACTION: Change your program to build a resource pool that can accommodate the key length of the file being opened. check my blog They appear on the JOB log. 004(04) Read past end of file 008(08) You attempted to store a record with a Duplicate Key, or there is a duplicate record for an

This circumstance could occur only if the file was built to a large size with a sharing option other than SHAREOPTIONS(4), and then altered (via the ALTER command) to SHAREOPTIONS(4). Return Code=0C Action=Request VSAM failed to read index-set records of an index. The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than expected, or an I/O error. PROGRAMMER ACTION: Rerun the job in a large partition.

X'24' 036 Return Code=08 Action=Request The key of the record to be inserted does not fall into an existing key range in the file. PROGRAMMER ACTION: Depends on the processing done during the preceding run. X'CC' 204 Return Code=08 Action=Request The program issued a PUT to insert a record while in backward mode. If the problem persists print the dump from the SYSDMP. (Refer to VSE/VSAM Access Method Service Logic for interpretation of the IDUMP output.) Contact your IBM Support Center.

X'64' 100 Return Code=08 Action=OPEN OPEN encountered an empty alternate index that is part of an upgrade set. An attempt was made to load a key-sequenced file with an access type other than keyed. If the system which opened the file has become inoperative, the lock can be released via Attention Routine UNLOCK command. (See VSE/Advanced Functions Systems Control Statements.) PROGRAMMER ACTION: Determine if the In most installations, this is not the common practice.

Rerun the job after the system problem is corrected. For sequential processing, this error code is set on for only the first record of the CI. View more information » PROGRAMMER ACTION: Change your job control statement to either use simplified job control or to correctly assign device to accommodate the volumes required for the cluster and its associated alternate indexes.

Open did not try to verify the file's catalog records.